1. Coats 700 Wheel Balancer
2. Coats 700 Balancer For Sale

Maintenance and Service

700 Solid State WHEEL BALANCER Installation Instructions Operating Instructions Safety Instructions Maintenance Instructions READ these instructions before placing unit in service KEEP these and other materials delivered. COATS 700 Balancer. iii. Read all instructions 2. Do not operate equipment with a damaged cord or if the equipment. Wheel balancers have had to change lately to accommodate the very large wheels now available for many cars. The thing is though, unless you run an auto shop that specialises in balancing modern wheels or selling tires for them, it may be better to outsource a few wheel balance jobs for larger wheels, and keep your old machine at least until we see where this large wheel trend ends. Before spinning the wheel. 4.ead and understand this manual before operat R - ing. Abuse and misuse will shorten the functional life. 5.e sure the balancer is properly connected to the B power supply and electrically grounded. Do not operate equipment with a damaged cord or if. Jun 30, 2016  Unite UB-1100 Wheel Balancer final cut Installation Operation(0728) - Duration: 5:14. Unite Auto Equipment LLC 54,806 views. COATS 700 Solid State Wheel Balancer User Manual. 4. coats 700 balancer. COATS Equipment. Manuals Directory ManualsDir.com - online owner manuals library. COATS manuals. Service Manual — COATS Models 700/700SS. 1 Introduction This service manual contains the functional checks, troubleshooting, adjustment, and part replacement instructions for COATS® Models 700 Wheel Balancer. Exploded views, illustrations, and an indexed parts. Hunter Engineering has a full-line of standard and heavy-duty wheel balancers that provide the fastest and most efficient balance. Learn more here about why you should have a Hunter wheel balancer.

Do not use solvents, which
leave an oily residue.

Never use compressed air
or a water hose to clean
any part of your balancer.

Preventative Maintenance
Daily

Clean shaft and faceplate with a vaporizing
solvent. Cones, hub nut, and other
mounting hardware should be checked and
cleaned.

Weekly

Thoroughly clean entire unit. Remove all
used weights, tools, and parts from under
and around balancer. Perform a calibration
check. Make calibration adjustments if
required.

ATTENTION: Maximum duty cycle is 40 wheels per
hours at 56 pounds.

NOTE: Before each balancing operation, make sure
that the back face of the wheel is clean. Use a wire
brush to clean the back face of the wheel if needed.

Service
If service should ever be required for your balancer,
contact the Service Department at (800) 688-6359.
Have your model and serial number ready.

Calibration Check Procedure
This procedure can be performed by the operator to
ensure the balancer is operating correctly and
properly calibrated. The only purpose of calibration is
to fine-tune the balancer to yield single-spin
balancing.

Use the fine balance mode during this procedure
(press and hold SHIFT and press ROUND OFF).

If the balancer fails to produce the results outlined in
this procedure, perform a calibration adjustment.

1.

Use normal mounting procedures to mount a
standard domestic 14, 15, or 16-inch diameter x
6 to 6-1/2-inch wide steel wheel with standard
tire mounted and properly inflated. Do not use a
wheel that is bent or misaligned. The center hole
must be free of nicks or burrs.

2.

Enter the offset, rim width, and wheel diameter
measurements into the balancer.

3.

Lower the hood and spin the wheel. Remember
to use the fine balance mode. Proceed to Step 4
when your weight displays read 0.10 ounces or
less (you may need to trim weights to
accomplish this).

4.

Raise the hood and attach a 4-ounce test weight

to the right side of the rim.

5.

Lower the hood and spin the wheel. The reading
in the right weight display should be between
3.85 and 4.15.

6.

Raise the hood and rotate the wheel until the
outer weight positioning lights flash. The test
weight should be in the 6 o’clock position. The
inner weight reading should be 0.15 ounces or
less (this figure is the result of the interference
between the two balancing planes).

7.

Repeat Steps 4, 5, and 6 with the test weight on
the left side of the rim.

Calibration Procedure
1.

Mount a wheel that best represents the
tire/wheel size most commonly balanced on this
unit. In most cases, this will be a 14, 15, or 16-
inch diameter by 6 to 6-1/2-inch wide wheel.
Remember to remove any weights attached to
the wheel.

2.

Enter the A (offset), W (width), and D (diameter)
measurements.

NOTE: It is important that you are accurate in
entering these measurements. Inaccurate
measurements will adversely affect your
calibration.

3.

Press and hold SHIFT and press CALIBRATE.
“CAL 0” will appear in the displays to indicate
Calibration Mode.

4.

Lower the hood and press START to spin the
wheel. Wait for the wheel to brake to a stop
before raising the hood.

5.

The balancer will indicate a 4-ounce weight in
ounce mode (100 grams in grams mode). Rotate
the wheel until the right weight positioning lights
blink. Attach the weight at top dead center on
the right plane.

REMEMBER: The more accurate you are in
locating the weight on the wheel, the more
accurate your calibration.

6.

Lower the hood and press START to respin the
wheel. When the wheel brakes to a stop,
calibration is complete and the balancer will
automatically exit the Calibration Mode.

6 • COATS 700 Balancer

CAUTION

CAUTION

Items 1 to 25 of 34 total

1. 1

ListGrid

1. Spring, 4 Cone System, 28mm

   For Models 600, 650, 700, 850, 1001, 1004 (4 Cone system - Prior to March 1992)

2. Cone, Large, old, 28mm

   3.00'-3.25' Center Holes - For 600, 650, 850, 1001, 1004 (4 Cone System - Prior to March 1992)

3. Cone, Medium, old, 28mm

   2.62'-3.00' Ctr Holes - For 600, 650, 850, 1001, 1004 (4 Cone System - Prior to March 1992)

4. Cone, Small, Old, 28mm

   2.25'-2.62' Ctr Holes - For 600, 650, 850, 1001, 1004 (4 Cone System - Prior to March 1992)

5. Cone, Miniature, old, 28mm

   1.70-2.25' Ctr Holes - For 600, 650, 700, 850, 1001, 1004 (4 Cone System - Prior to March 1992)

6. Lug Wrench

   Combi Adapter - Star Wrench Assembly

7. VW/Porche Adapter

   VW / Porsche Adapter, 28mm I.D., Bolt Circle Plate with Threaded Holes, 5x205mm, 5x130mm, Use vehicle lug bolts to attach wheel

8. Combo Adapter Kit, 28mm

   Combo Adapter Kit (3, 4, 5, 6, 8, 10 Lug), 1.125' (28mm) I.D., Range: 3' - 8' (75mm - 208mm)

9. Standard Balancer Chuck w/Plate, 28mm

   Range: 3.13' to 7.13', 3 Jaw Chuck, XL Pressure Drum, Chuck Key

10. Front Plate, Optional for Ext. Jaws, 28mm

    Backing Plate, 1.125' (28mm) I.D., for 19.5' hub centered wheels with centerhole from 8.52' to 8.89' (216.41-225.81mm)

11. Hub Piloted Budd Cone, 28mm

    Cone, 1.125' (28mm) I.D., for 19.5' hub centered wheels with centerhole from 8.52' to 8.89' (216.41-225.81mm)

12. Cone and Backing Plate Kit, 28mm

    Kit, Truck, 1.125' (28mm) I.D., Spacer & Cone for 19.5' hub centered wheels with centerhole from 8.52' to 8.89' (216.41-225.81mm) (same as 109877 for Model 6401 balancer)

13. GM/Chrysler Double Sided Plate, 28mm

    Offset Truck Wheel Adapter, GM/Chrysler Double Sided Adapter, 1.125' (28mm) I.D.

14. Ford Double Sided Plate, 28mm

    Offset Truck Wheel Adapter, Ford Double Sided Adapter, 1.125' (28mm) I.D.

15. Deep Offset Plate Set (3), 28mm

    Offset Truck Wheel Adapter Set, 1.125' (28mm) I.D., Ford Double Sided Adapter, GM/Chrysler 16' Double Sided Adapter, & Backing Plate

16. Fed-Ex Off Set Plate W/Backing, 28mm

    Offset Wheel Adapter Kit, 1.125' (28mm) I.D., Adapter & Backing Plate for 19.5' FedEx Wheel, 8.67'

17. In-Between Cone Set, 28MM

    In-Between Cone Set, 28MM (4) for wheels with shallow wheel centers

18. Backing Plate, 28mm

    Metal Backing Plate, 1.125' (28mm) I.D., 7.91' O.D., used with Offset Truck Wheel Adapters & Improved Light Truck Front Cone Kit

19. Light Truck Front Cone, 28mm

    Double Sided, Range: 4.80'-6.80'

20. Light Truck Cone Kit, 28mm

    Improved Light Truck Front Cone Kit, 28mm I.D., Double Sided Cone & Metal Backing Plate, Range: 4.80'-6.80'

21. Spacer - Light Trucks, 28mm

    Spacer - Light Trucks - 600, 650, 700, Used with 309069 cone.

22. Cone, Light Truck, 28mm

    3.375'-5.88' Ctr.Holes-For 600,650,700, used with 8309068 spacer.

23. Cone Kit, Light Trucks Up To One Ton, 28mm

    1.125' (28mm) I.D., Range: 3.375' To 5.88' (85.73-149.35mm), For models 600, 650, 700

24. Replacement Cone & Spring Set, 28mm

    4 cones & spring

25. Spring, 3 Cone System

    For Models 600, 650, 700, 850, 950, 1001,1004, 1050, 1055 (3 Cone System - From March 1992)

Items 1 to 25 of 34 total

Coats 700 Wheel Balancer

1. 1

Coats 700 Balancer For Sale

ListGrid